ON-SITE CONSTRUCTION

• Used when casting on soft ground, such as sand or heat insulation
• Does not break moisture barrier

• Used when casting on soft ground, such as sand or heat insulation
• Does not break moisture barrier
• Attaches to mesh
• Base plate with holes

• Facilitates and speeds up reinforcing work
• Length of linear spacer: 2m
• Model without openings for soft ground, for example, insulation
• Model with openings for hard ground
  

• Suitable between two separate meshes
• Stays well upright sue to it's shape
• Can be tied to bottom mesh
• Bearing of the product is 2000 x 180 mm
• Height 30-300 mm

632 SPACER

• Can be stacked
• Available concrete cover 50-150mm
• Stock colour: Grey
• For hard platform

• Robust, four legged spacer for construction companies and precast factories
• Available also with rounded legs
• Stock colour: Grey
• Both models can be nailed to surface
• Good grip on rebars

FLOOR AND WALL SPACER

• Stock colour: Grey
• Other colours by order
• Both models can be fastened with nail
• Can be first nailed to vertical wall and install rebars afterward.
  

BRIDGE SPACER

• Strong spacer for heavy reinforcing
• Available also with rounded legs
• Stock colour: Grey

BRIDGE SPACER LIGHT

• Strong spacer for heavy reinforcing
• Available also with rounded legs
• Stock colour: Grey

ALUMINIUM NAIL

• Pickled white. For fastening of spacers.
  
• Also for aluminium facades and roof plates, etc.
• Doesn't rost, for example rost stripes on plinth surface
  

620 SPACER

• Robust, four legged spacer for construction companies and precast factories
• Available also with rounded legs
• Stock colour: Grey
• Both models can be nailed to surface
• Good grip on rebars
  

BINDING WIRES

• High quality and resilient wire ensures tight bindings
  

TYING TOOL

• Normal with wooden handle
• Rubber handle with bearing, hardened tip and fully galvanized
  

• Used to fix insulation material to concrete
• For fastening extra insulation to element seam
• For fastening corner joint heat barrier in plinths 
• In precast fixing nail is pushed through insulation into soft concrete
• Stock colour: Black
  

• Used for fixing insulation on ground casted floors
• Can be used to attach two insulation plates to each other
  
• Fastener is screwed in it's place after installing the insulation plates and reinforcement steels

• To be used primarily in spots where post fitting of spacers is not possible, for example, in columns and beams

MESH SPACER CAP

• Stock colour: grey
• Used as an edge stopper to ensure sufficient cover and as protective plug for legs of reinforcing stand mounting racks

CONCRETE INSERT COVER PLATE

• Cover for concrete insert or lifting anchor
• Slightly curved surface
• True colour may differ from pictures
  

JOINT IRON BRACKET

• For supporting 265 mm cavity slab joint reinforcement. 
  
• It is possible to fasten to upper barbs, for example, a Ø 20 mm electric installation pipe, and to lower barbs a Ø 10-12 mm reinforcement.
  
• Product has been developed together with cavity slab fitters.
  

• Frame steel support can be  used for example supporting rebars of cavity joints on building sites
• For mounting the frame steel between element and outer cavity slab (ensures correct concrete cover for reinforcement).

• Facilitates heat barrier installation, speeds up casting preparations
• Need: 4-6 pcs / m²
• Use: In plywood/ board forms

SPACER TUBE

• AB spacer tube is used for supporting form and to ensure straightness of form surfaces and correct wall thickness
  
• Flanges and cones used in spacer tube are removed after casting and hole is filled with concrete
• Tube length: 2m
  

SEALING RING AND CASTING PLUG

• AB 22 casting plug prevents flow of leak waters through the tube in a water tight casting (for tube 22/26)
• ABT 22 sealing ring used on the outside surface of tube AB 22/26 to prevent penetration of the leak waters, recommendation 2-3 rings/tube

MALTHUS TIE ROD

• Suitable for normal wall castings
  
• Can be used with board formwork as well as shutter formwork
• Tail is easy to cut by hand

WATERTIGHT MALTHUS TIE ROD

Tie rod with steel disk must be used in outside walls of bomb shelters. Spacer is selected according to wall thickness

• For watertight and bomb shelter castings

MALTHUS FOR INSULATED WALLS

• For plinth splittings with insulation
• Enables casting for both plinth walls at the same time
• Made to measure at short notice

• Used when casting against old wall or rock.
  
• Made to measure at short notice.
  

• Used for tightening tie rods to formwork.
  
• Installed behind the washer at the end of the rod.
  

ABV WATER TIGHT CASTING ACCESSORIES

• Water tight casting is used, for example, in swimming pools, bomb shelters and in elevator shaft lower floors below the ground level.

• System consists of sealing plate TL,  branch lock HL, form cone ABV 12/25-KT and binding rod Ø 10 mm with or without welded flange (100 x 100 x 2 mm), lengths 1200 mm and 1500 mm.  

1. Sealing plate TL
2. Branch lock HL
3. Form cone ABV 12/25-KT
4. Binding rod Ø 10 mm, length 1200 mm and 1500 mm
5. Binding rod Ø 10 mm with welded flange (100 x 100 x 2 mm)

L = 1200 mm
Complete wall thicknesses 200, 250 and 300 mm

L = 1500 mm
Complete wall thicknesses 350, 400 and 450 mm.

FORM CONE

FORMWORK CLAMP

• Hot pressed wedge of tensile special alloy steel with hardened surface.
  
• Holds well both on smooth and ribbed rebars.
  
• Use: Round bar Ø 10-12 mm, ribbed bar Ø 8-10 mm.
  
• Zinc coated.
  

CLAMP TENSIONER

• Both models tension clamps tightly and efficiently.
  
• Suitable for tensioning most common clamp models.
  

ANCHOR NUT

• Flange nut 15/100
• Diameter 100 mm
  

FORM TIE ROD (DYWIDAG)

• Length 1,2 m
• By order 6 m

WORKING JOINT AND EXPANSION JOINT BAND

• Used, for example, for swimming pools, bomb shelters, lift shafts and other underground constructions.
  
• To be fastened to reinforcement by binding wire so that joint strip remains by half above the surface to be cast.
• Swelling band CJTA can be fastened to surface with glue or nails
  
• Also other models by order.
• (*)Only on order
  

ELEMENT MOUNTING PAD FOR LIGHT ELEMENTS

• Used for mounting of light partition wall elements and cavity slabs.
  
• Raw material is polyethene.
  
• Tested with 0 to 12 500kg load.
• Nominal capasity 3500kg
  

NOTE! Now packaged in moisture resistant plastic bag.

ELEMENT MOUNTING PAD FOR HEAVY ELEMENTS

• For mounting of heavy elements.
  
• Raw material is polycarbonate.
  
• Tested with 0 to 12 500 kg load. 
• Nominal capasity 10 000 kg
  

 Advantages compared to steel pad.

• Lighter to transport to installation site.
  
• No slippery frost layer formed on surface in winter.
  
• No rust runs.

Advantages compared to plywood pad.

• Doesn't have to be removed from construction
• Doesn't act as a substrate for microbes 

BLOCK MOUNTING WEDGES

Okaria wedges are easy to use, for example, in mounting of concrete blocks, doors and aluminium wall structures.

THRESHOLD PROTECTOR

• Construction phase threshold protector for balcony doors.
• For single and double wing door frames with depths of 170mm and 210 mm.
  
• Raw material shock proof PS plate, 1.5 mm. Length 890 mm.
  
• Threshold protector prevents damage to threshold during construction.
  
• Threshold protector is suitable for balcony doors and it is fastened by spring loaded stapler.
  
• Does not prevent closing of the door.
  
• Threshold seal should be removed when using threshold protector as door might be damaged due to excessive tightness.
  

MASONRY TUB

• Correct working level by means of a tub stand.
  
• Easy to clean.
  
• Good frost resistance.
• Capacity max 75 liters.
  
• Colour: black.
  
• OKAR TUB is produced from tough HDPE plastic plate by hot moulding and tolerates freeze extremely well
  
• Tub stand is a strong steel construction which stands well even in harsh use.

NAIL EXTRACTOR

• Length of handle 75 cm
  

FASTENING PROFILE

• Length 940 mm, width 85 mm and height 28 mm
  
• Installation rail enables 17 feed through sleeves for 20 mm electric tubes.
• Ensto AJ 10.20v.

INSULATION FASTENER

• A Ø 10 mm hole is drilled through insulation into concrete base to about 40 mm depth.
  
• Fastener is pushed into the hole and a plastic wedge pin is driven to level with flange surface with a hammer.
  

LIGHT FASTENER

• Used for fastening acoustic and insulation boards.
• Ø 8 mm hole is drilled through insulation into concrete base.
  
• Fastener is pushed into hole and driven to a depth of 20 – 30 mm with a hammer.
  

MINERAL WOOL FASTENER AND PUNCH DOWEL

BY ORDER ONLY

• A Ø 8 mm hole is drilled through insulation into concrete base.
• Fastener is pushed into the hole and a metal wedge is driven to anchoring part of fastener with punching dowel with hammer.

AP 60 NAIL WASHER

• Used for fastening wind barrier insulation boards to wood structure.
• Flange Ø 60 mm.
  

NAILING SPACER

• Used when mineral board is used as wind barrier.
  
• Sleeve like NOP gives solid platform for battening.
  
• Six legged OPNV is light to install through wool binding fabric.

TSOP BRICK BINDER

• By using together with nailing spacer wind pressure is transferred to framework and brick wall doesn't break
  
• Brick binder stands also pressing forces caused by wind pressure.
  
• Bricklaying of a timber framed family house is supported by TSOP brick binder.
  
• 100 mm nail.
• Length of gripping part 90 mm.
• Usage: 4pcs / m2
  

STAINLESS BRICK BINDER

• Brick binder, to be driven through insulation into wood frame, is easy and fast to install.
  
• Brick binder, to be driven into concrete base using a wedge, holds well and insulation to be installed afterwards can be fastened easily by means of locking plate.
• Mounting hole diam. 6 mm and depth approx. 40 mm
• Usage: 4pcs / m2

• Fastlock locking plate is a plastic flange with stainless steel locking washer in center which grips well to approx.
  
• Ø 4 mm metal wire.
• Flange Ø 80 mm.
  

REBAR SAFETY CAP

Safety cap is used as warning sign of freely protruding rod ends, for example to prevent tearing of protective cover sheets and improve working safety. Cap is clearly visible due to its alert colour.

• It is used also as protection in element storage and transportation.
• ABX 8-16: orange for 8-16 mm iron
  
• ABX 16-30: orange for 16-30 mm iron
  
• ABX 25-40: orange for 25-40 mm iron
  

ALIGNMENT PLATE

Manufactured from frostproof plastic. Colours facilitate distinguishing between different alignments. ASL alignment plate is easy to fasten firmly with stapler. Central groove facilitates bending of plate around corner. It is possible to make markings on ASL alignment plate with a waterproof felt tip pen.

• Stock colours: yellow, blue, red, white and orange.
  
• Total length: 250 mm.

DRILLING PLUG

• Drilling plug prevents soil shifted by drain water from entering the drill hole.
  
• Drilling plug prevents loose stones from entering the drill hole, which in worst case could prevent charging of the hole.
  
• Drilling plug also indicates location of drill hole. Our selection includes 6 different size drilling plugs.
  
• Drilling plugs are packed in weather proof plastic sacks.
  
• Okaria drilling plugs can be reused. They can be collected and stored in small space due to stacking possibility.
  

SITE FENCE

Site fence creates smart facade for construction site and a clear boundary. Long lasting fence is easy to use and handle. Thin fence strand can stand a load of up to 60 kg. Good throughflow properties for wind have been developed in a wind tunnel.Dirt and colouring agent resistant raw material is recyclable, UV protected and frostproof.

SIGNAL LINE

• Separates work sites clearly.
  
• Dangerous areas can be marked and segregated efficiently and fast with siganal line.
  
• Frostproof
• Reflecting tag
• Red/yellow.
  
• Length 25 m.

TRAFFIC POLE WITH RUBBER STAND

Traffic pole is suitable for traffic control or for delimiting an area. Through coloured red, UV protected HD polyethene. Fastening holes at upper end for sealing-off line.

• Well visible, fast to erect.
• Equipped with reflectors.
  
• Height of traffic pole is 1000 mm and diameter 110 mm.
  
• Size of rubber stand is 400 x 400 mm, height 85 mm and weight 7 kg.

MARKING PLATES

With or without printing.

• Printing is done by hot folio printing.
  
• Printing colour is black or as agreed.
• Printing can be single or double sided.
  
• Stock colours of marking plates vary by product.

ANGLE MOULDING

• Stock colour: white.
  
• Special colours on order.
  

FOOT LEDGE

• Stock colours: white and grey.
  
• Special colours on order.
  

ARCHITRAVE

• Stock colours: white and grey.
  
• Special colours on order.
  
• Also 2700 mm long by order.